Файловый менеджер

Файловый менеджер - Редактировать - /usr/src/linux-headers-5.4.0-200/drivers/input/misc/Kconfig

Назад
# SPDX-License-Identifier: GPL-2.0-only # # Input misc drivers configuration # menuconfig INPUT_MISC bool "Miscellaneous devices" help Say Y here, and a list of miscellaneous input drivers will be displayed. Everything that didn't fit into the other categories is here. This option doesn't affect the kernel. If unsure, say Y. if INPUT_MISC config INPUT_88PM860X_ONKEY tristate "88PM860x ONKEY support" depends on MFD_88PM860X help Support the ONKEY of Marvell 88PM860x PMICs as an input device reporting power button status. To compile this driver as a module, choose M here: the module will be called 88pm860x_onkey. config INPUT_88PM80X_ONKEY tristate "88PM80x ONKEY support" depends on MFD_88PM800 help Support the ONKEY of Marvell 88PM80x PMICs as an input device reporting power button status. To compile this driver as a module, choose M here: the module will be called 88pm80x_onkey. config INPUT_AB8500_PONKEY tristate "AB8500 Pon (PowerOn) Key" depends on AB8500_CORE help Say Y here to use the PowerOn Key for ST-Ericsson's AB8500 Mix-Sig PMIC. To compile this driver as a module, choose M here: the module will be called ab8500-ponkey. config INPUT_AD714X tristate "Analog Devices AD714x Capacitance Touch Sensor" help Say Y here if you want to support an AD7142/3/7/8/7A touch sensor. You should select a bus connection too. To compile this driver as a module, choose M here: the module will be called ad714x. config INPUT_AD714X_I2C tristate "support I2C bus connection" depends on INPUT_AD714X && I2C default y help Say Y here if you have AD7142/AD7147 hooked to an I2C bus. To compile this driver as a module, choose M here: the module will be called ad714x-i2c. config INPUT_AD714X_SPI tristate "support SPI bus connection" depends on INPUT_AD714X && SPI default y help Say Y here if you have AD7142/AD7147 hooked to a SPI bus. To compile this driver as a module, choose M here: the module will be called ad714x-spi. config INPUT_ARIZONA_HAPTICS tristate "Arizona haptics support" depends on MFD_ARIZONA && SND_SOC select INPUT_FF_MEMLESS help Say Y to enable support for the haptics module in Arizona CODECs. To compile this driver as a module, choose M here: the module will be called arizona-haptics. config INPUT_ATMEL_CAPTOUCH tristate "Atmel Capacitive Touch Button Driver" depends on OF \|\| COMPILE_TEST depends on I2C help Say Y here if an Atmel Capacitive Touch Button device which implements "captouch" protocol is connected to I2C bus. Typically this device consists of Atmel Touch sensor controlled by AtMegaXX MCU running firmware based on Qtouch library. One should find "atmel,captouch" node in the board specific DTS. To compile this driver as a module, choose M here: the module will be called atmel_captouch. config INPUT_BMA150 tristate "BMA150/SMB380 acceleration sensor support" depends on I2C select INPUT_POLLDEV help Say Y here if you have Bosch Sensortec's BMA150 or SMB380 acceleration sensor hooked to an I2C bus. To compile this driver as a module, choose M here: the module will be called bma150. config INPUT_E3X0_BUTTON tristate "NI Ettus Research USRP E3xx Button support." default n help Say Y here to enable support for the NI Ettus Research USRP E3xx Button. To compile this driver as a module, choose M here: the module will be called e3x0_button. config INPUT_MSM_VIBRATOR tristate "Qualcomm MSM vibrator driver" select INPUT_FF_MEMLESS help Support for the vibrator that is found on various Qualcomm MSM SOCs. To compile this driver as a module, choose M here: the module will be called msm_vibrator. config INPUT_PCSPKR tristate "PC Speaker support" depends on PCSPKR_PLATFORM help Say Y here if you want the standard PC Speaker to be used for bells and whistles. If unsure, say Y. To compile this driver as a module, choose M here: the module will be called pcspkr. config INPUT_PM8941_PWRKEY tristate "Qualcomm PM8941 power key support" depends on MFD_SPMI_PMIC help Say Y here if you want support for the power key usually found on boards using a Qualcomm PM8941 compatible PMIC. If unsure, say Y. To compile this driver as a module, choose M here: the module will be called pm8941-pwrkey. config INPUT_PM8XXX_VIBRATOR tristate "Qualcomm PM8XXX vibrator support" depends on MFD_PM8XXX \|\| MFD_SPMI_PMIC select INPUT_FF_MEMLESS help This option enables device driver support for the vibrator on Qualcomm PM8xxx chip. This driver supports ff-memless interface from input framework. To compile this driver as module, choose M here: the module will be called pm8xxx-vibrator. config INPUT_PMIC8XXX_PWRKEY tristate "PMIC8XXX power key support" depends on MFD_PM8XXX help Say Y here if you want support for the PMIC8XXX power key. If unsure, say N. To compile this driver as a module, choose M here: the module will be called pmic8xxx-pwrkey. config INPUT_SPARCSPKR tristate "SPARC Speaker support" depends on PCI && SPARC64 help Say Y here if you want the standard Speaker on Sparc PCI systems to be used for bells and whistles. If unsure, say Y. To compile this driver as a module, choose M here: the module will be called sparcspkr. config INPUT_M68K_BEEP tristate "M68k Beeper support" depends on M68K config INPUT_MAX77650_ONKEY tristate "Maxim MAX77650 ONKEY support" depends on MFD_MAX77650 help Support the ONKEY of the MAX77650 PMIC as an input device. To compile this driver as a module, choose M here: the module will be called max77650-onkey. config INPUT_MAX77693_HAPTIC tristate "MAXIM MAX77693/MAX77843 haptic controller support" depends on (MFD_MAX77693 \|\| MFD_MAX77843) && PWM select INPUT_FF_MEMLESS help This option enables support for the haptic controller on MAXIM MAX77693 and MAX77843 chips. To compile this driver as module, choose M here: the module will be called max77693-haptic. config INPUT_MAX8925_ONKEY tristate "MAX8925 ONKEY support" depends on MFD_MAX8925 help Support the ONKEY of MAX8925 PMICs as an input device reporting power button status. To compile this driver as a module, choose M here: the module will be called max8925_onkey. config INPUT_MAX8997_HAPTIC tristate "MAXIM MAX8997 haptic controller support" depends on PWM && MFD_MAX8997 select INPUT_FF_MEMLESS help This option enables device driver support for the haptic controller on MAXIM MAX8997 chip. This driver supports ff-memless interface from input framework. To compile this driver as module, choose M here: the module will be called max8997-haptic. config INPUT_MC13783_PWRBUTTON tristate "MC13783 ON buttons" depends on MFD_MC13XXX help Support the ON buttons of MC13783 PMIC as an input device reporting power button status. To compile this driver as a module, choose M here: the module will be called mc13783-pwrbutton. config INPUT_MMA8450 tristate "MMA8450 - Freescale's 3-Axis, 8/12-bit Digital Accelerometer" depends on I2C select INPUT_POLLDEV help Say Y here if you want to support Freescale's MMA8450 Accelerometer through I2C interface. To compile this driver as a module, choose M here: the module will be called mma8450. config INPUT_APANEL tristate "Fujitsu Lifebook Application Panel buttons" depends on X86 && I2C && LEDS_CLASS select INPUT_POLLDEV select CHECK_SIGNATURE help Say Y here for support of the Application Panel buttons, used on Fujitsu Lifebook. These are attached to the mainboard through an SMBus interface managed by the I2C Intel ICH (i801) driver, which you should also build for this kernel. To compile this driver as a module, choose M here: the module will be called apanel. config INPUT_GP2A tristate "Sharp GP2AP002A00F I2C Proximity/Opto sensor driver" depends on I2C depends on GPIOLIB \|\| COMPILE_TEST help Say Y here if you have a Sharp GP2AP002A00F proximity/als combo-chip hooked to an I2C bus. To compile this driver as a module, choose M here: the module will be called gp2ap002a00f. config INPUT_GPIO_BEEPER tristate "Generic GPIO Beeper support" depends on GPIOLIB \|\| COMPILE_TEST help Say Y here if you have a beeper connected to a GPIO pin. To compile this driver as a module, choose M here: the module will be called gpio-beeper. config INPUT_GPIO_DECODER tristate "Polled GPIO Decoder Input driver" depends on GPIOLIB \|\| COMPILE_TEST select INPUT_POLLDEV help Say Y here if you want driver to read status of multiple GPIO lines and report the encoded value as an absolute integer to input subsystem. To compile this driver as a module, choose M here: the module will be called gpio_decoder. config INPUT_GPIO_VIBRA tristate "GPIO vibrator support" depends on GPIOLIB \|\| COMPILE_TEST select INPUT_FF_MEMLESS help Say Y here to get support for GPIO based vibrator devices. If unsure, say N. To compile this driver as a module, choose M here: the module will be called gpio-vibra. config INPUT_IXP4XX_BEEPER tristate "IXP4XX Beeper support" depends on ARCH_IXP4XX help If you say yes here, you can connect a beeper to the ixp4xx gpio pins. This is used by the LinkSys NSLU2. If unsure, say Y. To compile this driver as a module, choose M here: the module will be called ixp4xx-beeper. config INPUT_COBALT_BTNS tristate "Cobalt button interface" depends on MIPS_COBALT select INPUT_POLLDEV help Say Y here if you want to support MIPS Cobalt button interface. To compile this driver as a module, choose M here: the module will be called cobalt_btns. config INPUT_CPCAP_PWRBUTTON tristate "CPCAP OnKey" depends on MFD_CPCAP help Say Y here if you want to enable power key reporting via the Motorola CPCAP chip. To compile this driver as a module, choose M here. The module will be called cpcap-pwrbutton. config INPUT_WISTRON_BTNS tristate "x86 Wistron laptop button interface" depends on X86_32 select INPUT_POLLDEV select INPUT_SPARSEKMAP select NEW_LEDS select LEDS_CLASS select CHECK_SIGNATURE help Say Y here for support of Wistron laptop button interfaces, used on laptops of various brands, including Acer and Fujitsu-Siemens. If available, mail and wifi LEDs will be controllable via /sys/class/leds. To compile this driver as a module, choose M here: the module will be called wistron_btns. config INPUT_ATLAS_BTNS tristate "x86 Atlas button interface" depends on X86 && ACPI help Say Y here for support of Atlas wallmount touchscreen buttons. The events will show up as scancodes F1 through F9 via evdev. To compile this driver as a module, choose M here: the module will be called atlas_btns. config INPUT_ATI_REMOTE2 tristate "ATI / Philips USB RF remote control" depends on USB_ARCH_HAS_HCD select USB help Say Y here if you want to use an ATI or Philips USB RF remote control. These are RF remotes with USB receivers. ATI Remote Wonder II comes with some ATI's All-In-Wonder video cards and is also available as a separate product. This driver provides mouse pointer, left and right mouse buttons, and maps all the other remote buttons to keypress events. To compile this driver as a module, choose M here: the module will be called ati_remote2. config INPUT_KEYSPAN_REMOTE tristate "Keyspan DMR USB remote control" depends on USB_ARCH_HAS_HCD select USB help Say Y here if you want to use a Keyspan DMR USB remote control. Currently only the UIA-11 type of receiver has been tested. The tag on the receiver that connects to the USB port should have a P/N that will tell you what type of DMR you have. The UIA-10 type is not supported at this time. This driver maps all buttons to keypress events. To compile this driver as a module, choose M here: the module will be called keyspan_remote. config INPUT_KXTJ9 tristate "Kionix KXTJ9 tri-axis digital accelerometer" depends on I2C help Say Y here to enable support for the Kionix KXTJ9 digital tri-axis accelerometer. To compile this driver as a module, choose M here: the module will be called kxtj9. config INPUT_KXTJ9_POLLED_MODE bool "Enable polling mode support" depends on INPUT_KXTJ9 select INPUT_POLLDEV help Say Y here if you need accelerometer to work in polling mode. config INPUT_POWERMATE tristate "Griffin PowerMate and Contour Jog support" depends on USB_ARCH_HAS_HCD select USB help Say Y here if you want to use Griffin PowerMate or Contour Jog devices. These are aluminum dials which can measure clockwise and anticlockwise rotation. The dial also acts as a pushbutton. The base contains an LED which can be instructed to pulse or to switch to a particular intensity. You can download userspace tools from <http://sowerbutts.com/powermate/>. To compile this driver as a module, choose M here: the module will be called powermate. config INPUT_YEALINK tristate "Yealink usb-p1k voip phone" depends on USB_ARCH_HAS_HCD select USB help Say Y here if you want to enable keyboard and LCD functions of the Yealink usb-p1k usb phones. The audio part is enabled by the generic usb sound driver, so you might want to enable that as well. For information about how to use these additional functions, see <file:Documentation/input/devices/yealink.rst>. To compile this driver as a module, choose M here: the module will be called yealink. config INPUT_CM109 tristate "C-Media CM109 USB I/O Controller" depends on USB_ARCH_HAS_HCD select USB help Say Y here if you want to enable keyboard and buzzer functions of the C-Media CM109 usb phones. The audio part is enabled by the generic usb sound driver, so you might want to enable that as well. To compile this driver as a module, choose M here: the module will be called cm109. config INPUT_REGULATOR_HAPTIC tristate "Regulator haptics support" depends on REGULATOR select INPUT_FF_MEMLESS help This option enables device driver support for the haptic controlled by a regulator. This driver supports ff-memless interface from input framework. To compile this driver as a module, choose M here: the module will be called regulator-haptic. config INPUT_RETU_PWRBUTTON tristate "Retu Power button Driver" depends on MFD_RETU help Say Y here if you want to enable power key reporting via the Retu chips found in Nokia Internet Tablets (770, N800, N810). To compile this driver as a module, choose M here. The module will be called retu-pwrbutton. config INPUT_TPS65218_PWRBUTTON tristate "TPS65218 Power button driver" depends on (MFD_TPS65217 \|\| MFD_TPS65218) help Say Y here if you want to enable power button reporting for TPS65217 and TPS65218 Power Management IC devices. To compile this driver as a module, choose M here. The module will be called tps65218-pwrbutton. config INPUT_AXP20X_PEK tristate "X-Powers AXP20X power button driver" depends on MFD_AXP20X help Say Y here if you want to enable power key reporting via the AXP20X PMIC. To compile this driver as a module, choose M here. The module will be called axp20x-pek. config INPUT_TWL4030_PWRBUTTON tristate "TWL4030 Power button Driver" depends on TWL4030_CORE help Say Y here if you want to enable power key reporting via the TWL4030 family of chips. To compile this driver as a module, choose M here. The module will be called twl4030_pwrbutton. config INPUT_TWL4030_VIBRA tristate "Support for TWL4030 Vibrator" depends on TWL4030_CORE select MFD_TWL4030_AUDIO select INPUT_FF_MEMLESS help This option enables support for TWL4030 Vibrator Driver. To compile this driver as a module, choose M here. The module will be called twl4030_vibra. config INPUT_TWL6040_VIBRA tristate "Support for TWL6040 Vibrator" depends on TWL6040_CORE select INPUT_FF_MEMLESS help This option enables support for TWL6040 Vibrator Driver. To compile this driver as a module, choose M here. The module will be called twl6040_vibra. config INPUT_UINPUT tristate "User level driver support" help Say Y here if you want to support user level drivers for input subsystem accessible under char device 10:223 - /dev/input/uinput. To compile this driver as a module, choose M here: the module will be called uinput. config INPUT_SGI_BTNS tristate "SGI Indy/O2 volume button interface" depends on SGI_IP22 \|\| SGI_IP32 select INPUT_POLLDEV help Say Y here if you want to support SGI Indy/O2 volume button interface. To compile this driver as a module, choose M here: the module will be called sgi_btns. config HP_SDC_RTC tristate "HP SDC Real Time Clock" depends on (GSC \|\| HP300) && SERIO select HP_SDC help Say Y here if you want to support the built-in real time clock of the HP SDC controller. config INPUT_PALMAS_PWRBUTTON tristate "Palmas Power button Driver" depends on MFD_PALMAS help Say Y here if you want to enable power key reporting via the Palmas family of PMICs. To compile this driver as a module, choose M here. The module will be called palmas_pwrbutton. config INPUT_PCF50633_PMU tristate "PCF50633 PMU events" depends on MFD_PCF50633 help Say Y to include support for delivering PMU events via input layer on NXP PCF50633. config INPUT_PCF8574 tristate "PCF8574 Keypad input device" depends on I2C help Say Y here if you want to support a keypad connected via I2C with a PCF8574. To compile this driver as a module, choose M here: the module will be called pcf8574_keypad. config INPUT_PWM_BEEPER tristate "PWM beeper support" depends on PWM help Say Y here to get support for PWM based beeper devices. If unsure, say N. To compile this driver as a module, choose M here: the module will be called pwm-beeper. config INPUT_PWM_VIBRA tristate "PWM vibrator support" depends on PWM select INPUT_FF_MEMLESS help Say Y here to get support for PWM based vibrator devices. If unsure, say N. To compile this driver as a module, choose M here: the module will be called pwm-vibra. config INPUT_RK805_PWRKEY tristate "Rockchip RK805 PMIC power key support" depends on MFD_RK808 help Select this option to enable power key driver for RK805. If unsure, say N. To compile this driver as a module, choose M here: the module will be called rk805_pwrkey. config INPUT_GPIO_ROTARY_ENCODER tristate "Rotary encoders connected to GPIO pins" depends on GPIOLIB \|\| COMPILE_TEST help Say Y here to add support for rotary encoders connected to GPIO lines. Check file:Documentation/input/devices/rotary-encoder.rst for more information. To compile this driver as a module, choose M here: the module will be called rotary_encoder. config INPUT_RB532_BUTTON tristate "Mikrotik Routerboard 532 button interface" depends on MIKROTIK_RB532 depends on GPIOLIB select INPUT_POLLDEV help Say Y here if you want support for the S1 button built into Mikrotik's Routerboard 532. To compile this driver as a module, choose M here: the module will be called rb532_button. config INPUT_DA9052_ONKEY tristate "Dialog DA9052/DA9053 Onkey" depends on PMIC_DA9052 help Support the ONKEY of Dialog DA9052 PMICs as an input device reporting power button status. To compile this driver as a module, choose M here: the module will be called da9052_onkey. config INPUT_DA9055_ONKEY tristate "Dialog Semiconductor DA9055 ONKEY" depends on MFD_DA9055 help Support the ONKEY of DA9055 PMICs as an input device reporting power button status. To compile this driver as a module, choose M here: the module will be called da9055_onkey. config INPUT_DA9063_ONKEY tristate "Dialog DA9063/62/61 OnKey" depends on MFD_DA9063 \|\| MFD_DA9062 help Support the ONKEY of Dialog DA9063, DA9062 and DA9061 Power Management ICs as an input device capable of reporting the power button status. To compile this driver as a module, choose M here: the module will be called da9063_onkey. config INPUT_DM355EVM tristate "TI DaVinci DM355 EVM Keypad and IR Remote" depends on MFD_DM355EVM_MSP select INPUT_SPARSEKMAP help Supports the pushbuttons and IR remote used with the DM355 EVM board. To compile this driver as a module, choose M here: the module will be called dm355evm_keys. config INPUT_WM831X_ON tristate "WM831X ON pin" depends on MFD_WM831X help Support the ON pin of WM831X PMICs as an input device reporting power button status. To compile this driver as a module, choose M here: the module will be called wm831x_on. config INPUT_PCAP tristate "Motorola EZX PCAP misc input events" depends on EZX_PCAP help Say Y here if you want to use Power key and Headphone button on Motorola EZX phones. To compile this driver as a module, choose M here: the module will be called pcap_keys. config INPUT_ADXL34X tristate "Analog Devices ADXL34x Three-Axis Digital Accelerometer" default n help Say Y here if you have a Accelerometer interface using the ADXL345/6 controller, and your board-specific initialization code includes that in its table of devices. This driver can use either I2C or SPI communication to the ADXL345/6 controller. Select the appropriate method for your system. If unsure, say N (but it's safe to say "Y"). To compile this driver as a module, choose M here: the module will be called adxl34x. config INPUT_ADXL34X_I2C tristate "support I2C bus connection" depends on INPUT_ADXL34X && I2C default y help Say Y here if you have ADXL345/6 hooked to an I2C bus. To compile this driver as a module, choose M here: the module will be called adxl34x-i2c. config INPUT_ADXL34X_SPI tristate "support SPI bus connection" depends on INPUT_ADXL34X && SPI default y help Say Y here if you have ADXL345/6 hooked to a SPI bus. To compile this driver as a module, choose M here: the module will be called adxl34x-spi. config INPUT_IMS_PCU tristate "IMS Passenger Control Unit driver" depends on USB depends on LEDS_CLASS help Say Y here if you have system with IMS Rave Passenger Control Unit. To compile this driver as a module, choose M here: the module will be called ims_pcu. config INPUT_CMA3000 tristate "VTI CMA3000 Tri-axis accelerometer" help Say Y here if you want to use VTI CMA3000_D0x Accelerometer driver This driver currently only supports I2C interface to the controller. Also select the I2C method. If unsure, say N To compile this driver as a module, choose M here: the module will be called cma3000_d0x. config INPUT_CMA3000_I2C tristate "Support I2C bus connection" depends on INPUT_CMA3000 && I2C help Say Y here if you want to use VTI CMA3000_D0x Accelerometer through I2C interface. To compile this driver as a module, choose M here: the module will be called cma3000_d0x_i2c. config INPUT_XEN_KBDDEV_FRONTEND tristate "Xen virtual keyboard and mouse support" depends on XEN default y select XEN_XENBUS_FRONTEND help This driver implements the front-end of the Xen virtual keyboard and mouse device driver. It communicates with a back-end in another domain. To compile this driver as a module, choose M here: the module will be called xen-kbdfront. config INPUT_SIRFSOC_ONKEY tristate "CSR SiRFSoC power on/off/suspend key support" depends on ARCH_SIRF && OF default y help Say Y here if you want to support for the SiRFSoC power on/off/suspend key in Linux, after you press the onkey, system will suspend. If unsure, say N. config INPUT_IDEAPAD_SLIDEBAR tristate "IdeaPad Laptop Slidebar" depends on INPUT depends on SERIO_I8042 help Say Y here if you have an IdeaPad laptop with a slidebar. To compile this driver as a module, choose M here: the module will be called ideapad_slidebar. config INPUT_SOC_BUTTON_ARRAY tristate "Windows-compatible SoC Button Array" depends on KEYBOARD_GPIO && ACPI help Say Y here if you have a SoC-based tablet that originally runs Windows 8 or a Microsoft Surface Book 2, Pro 5, Laptop 1 or later. To compile this driver as a module, choose M here: the module will be called soc_button_array. config INPUT_DRV260X_HAPTICS tristate "TI DRV260X haptics support" depends on INPUT && I2C depends on GPIOLIB \|\| COMPILE_TEST select INPUT_FF_MEMLESS select REGMAP_I2C help Say Y to enable support for the TI DRV260X haptics driver. To compile this driver as a module, choose M here: the module will be called drv260x-haptics. config INPUT_DRV2665_HAPTICS tristate "TI DRV2665 haptics support" depends on INPUT && I2C select INPUT_FF_MEMLESS select REGMAP_I2C help Say Y to enable support for the TI DRV2665 haptics driver. To compile this driver as a module, choose M here: the module will be called drv2665-haptics. config INPUT_DRV2667_HAPTICS tristate "TI DRV2667 haptics support" depends on INPUT && I2C select INPUT_FF_MEMLESS select REGMAP_I2C help Say Y to enable support for the TI DRV2667 haptics driver. To compile this driver as a module, choose M here: the module will be called drv2667-haptics. config INPUT_HISI_POWERKEY tristate "Hisilicon PMIC ONKEY support" depends on ARCH_HISI \|\| COMPILE_TEST help Say Y to enable support for PMIC ONKEY. To compile this driver as a module, choose M here: the module will be called hisi_powerkey. config INPUT_RAVE_SP_PWRBUTTON tristate "RAVE SP Power button Driver" depends on RAVE_SP_CORE help Say Y here if you want to enable power key reporting from RAVE SP To compile this driver as a module, choose M here: the module will be called rave-sp-pwrbutton. config INPUT_SC27XX_VIBRA tristate "Spreadtrum sc27xx vibrator support" depends on MFD_SC27XX_PMIC \|\| COMPILE_TEST select INPUT_FF_MEMLESS help This option enables support for Spreadtrum sc27xx vibrator driver. To compile this driver as a module, choose M here. The module will be called sc27xx_vibra. config INPUT_STPMIC1_ONKEY tristate "STPMIC1 PMIC Onkey support" depends on MFD_STPMIC1 help Say Y to enable support of onkey embedded into STPMIC1 PMIC. onkey can be used to wakeup from low power modes and force a shut-down on long press. To compile this driver as a module, choose M here: the module will be called stpmic1_onkey. endif

| ver. 1.4 | Github | . | PHP 7.4.3-4ubuntu2.24 | Генерация страницы: 0 | proxy | phpinfo | Настройка